Brightness Test

Near-black squares from 1 to 40 on pure black. You should see square 2 or 3 and up while the background stays black. Click the pattern or press F for fullscreen.

Click for fullscreen · Click or Space next pattern · Esc exitTap for fullscreen, then tapTap for the next pattern

Find the lowest number you can see against the black.1–3 pattern · Space next · H hide controls
Faintest square you can see:

Pick the lowest number you can make out to get a verdict.

How to run the brightness test

  1. Use your normal lighting. Black level depends on the room: the same screen shows more shadow detail in the dark than next to a sunny window. Test where you actually use the screen. Turn off auto-brightness, Night Light / Night Shift and any eye-care mode.
  2. Let it warm up. LCD backlights and OLED panels settle after 15–30 minutes.
  3. Go fullscreen. Press F or click the pattern. White page content around the pattern makes your eyes adapt to bright and hides the faint squares.
  4. Find the faintest square. Look at each square in turn; the number under it is its level out of 255. Give your eyes a few seconds to adapt, then pick the lowest number you can see in the list under the pattern.
  5. Adjust and repeat. Change the setting the verdict suggests, then check the PLUGE bars (2) and the 0–31 grid (3), where every level touches the next so merged steps are easy to spot.

What good and bad look like

The rows below simulate how the squares come out under the most common problems. They are rendered on your own screen, so they are hard to see in a bright room — that is part of the point.

Correct — every step visible, 0 is black
Crushed — Brightness too low or gamma too high: the first steps merge into black
Raised — Brightness too high: steps visible but black is gray
RGB range mismatch — everything below 16 is black
Simulation of levels 0–40 (numbers underneath) on a correctly set screen and three common faults.
Faintest square you seeMeaningWhat to do
1–3Excellent shadow detailNothing, as long as the background still looks black. If it looks dark gray in a dim room, lower Brightness (TV: Brightness / Black level) one step at a time until square 1 just fades.
4–6Normal for many LCDs, especially in a bright roomOptional: raise Brightness a notch or two, or dim the room. Turn off ECO and dynamic contrast modes.
7–15Crushed shadows: dark detail is lostRaise Brightness (TV: Brightness / Black level). Check the Gamma setting isn’t above 2.2–2.4 with the gamma test.
Only 20 and aboveRGB range mismatch (full vs limited)Make the graphics card and the display agree on the RGB range — see below.

Brightness, backlight and black level are different things

The names on monitors and TVs don’t match, which is why “turn up the brightness” often does the wrong thing:

A good everyday light output is roughly the brightness of a sheet of white paper in the same room: blinding means too high, dull and gray means too low. The contrast test checks the other end of the scale, where highlights can clip to white.

Fix: only 20 and above visible (RGB range mismatch)

PCs send full range video (black = 0, white = 255). TVs and some monitors on HDMI expect limited range (black = 16, white = 235). If the graphics card sends full range and the display interprets it as limited, everything from 0 to 16 becomes black and 235–255 becomes white: this test shows 1–15 as invisible, and the contrast test loses its top squares. The opposite mismatch makes black look gray and washed out. Fix it in one place, not both:

Set it in only one place. Full range on the PC with full range on the display is correct. Limited on both is also correct. Mixing them is what crushes or washes out blacks.

Fix: crushed shadows (7–15)

Raised blacks: when the background looks gray

If you can see every square easily but the black background itself looks dark gray or bluish in a dim room, the black level is too high or you are looking at the panel’s native black. Lower Brightness on a TV, check the RGB range as above, and remember the limits of the technology: LCD black is never fully dark, IPS panels show a glow from an angle, and QD-OLED panels look less deep in a brightly lit room. Check the corners for light leaks with the backlight bleed test.

Frequently asked questions

How do I set my monitor’s brightness correctly?

Show the black level squares in fullscreen in your normal lighting. Raise Brightness until you can see square 1 or 2 against the black background, but stop before the background itself turns gray. On a typical LCD monitor the OSD Brightness changes the backlight, so set it for comfort first (about the same brightness as a sheet of white paper in your room), then use this test to confirm no shadow detail is lost.

Which squares should I be able to see?

On a well-set display you should see square 2 or 3 and up, and ideally square 1 in a dim room. Not seeing 1–4 in a bright room is normal on many LCDs. If you can’t see anything until 7 or higher, shadows are crushed. If 1–15 are all invisible but 20 is clear, your PC and display disagree about the RGB range.

What is the difference between brightness, backlight and black level?

On most PC monitors, “Brightness” dims or brightens the backlight, which changes how bright the whole picture is. On TVs, “Brightness” usually means black level: it shifts the darkest tones up or down, and the light output is called Backlight, OLED Light or Peak Brightness. Black level is the setting this test helps with; backlight is a comfort setting.

Why are blacks gray on my IPS or VA monitor?

LCDs can’t switch the backlight off for black pixels, so black is always slightly lit: IPS panels typically reach about 1000:1 contrast, VA panels several times more. In a dark room this looks dark gray, and IPS panels add a glow in the corners when viewed from close up. That is normal. OLED and mini-LED screens can show much deeper black.

Why can’t I see the first squares on my OLED?

Some OLEDs, especially older TVs and many phones in their vivid modes, clip or crush the first few levels above black to avoid near-black noise and blotches. Use the most accurate picture mode (Filmmaker, Cinema or Natural) and check that black level is set to Auto or Low/Limited only when the source is limited range. The OLED test has more near-black checks.

Does this test measure brightness in nits?

No. A web page can’t measure light output — that needs a light meter or colorimeter. What it can show is whether the darkest shades are being reproduced, which is what the brightness (black level) setting controls. For general use, many people find 100–200 nits comfortable indoors; photo editors often use 80–120 nits in a dim room.

Should I turn on auto-brightness on my phone or laptop?

For everyday use, yes — it saves battery and keeps the screen comfortable. For this test, turn it off (and turn off Night Shift, Night Light or Eye Comfort) so the screen doesn’t change while you look at it.

Last updated . Runs entirely in your browser — nothing is uploaded.