Before you start
- Warm it up. Leave the TV on for 20–30 minutes. Uniformity and color change as the panel warms, and some tint or clouding fades.
- Pick an accurate picture mode. Movie, Cinema, Filmmaker Mode or Calibrated. Turn off energy saving and ambient light sensors (they change brightness mid-test), and set sharpness to 0 or its neutral value.
- Choose how to show the test. Best: a laptop connected by HDMI at the TV’s native resolution, page fullscreen. Good: the TV’s own browser. OK for the first three steps only: casting a browser tab.
- Darken the room for the black-level and uniformity steps, and sit at your normal viewing position, centered.
How to run the TV screen test
- Go fullscreen. Press F on a keyboard, select the fullscreen button with the remote, or click the test. The patterns must reach the edges of the panel.
- Look at every pattern in a step. Press ◀ and ▶ on the remote (or click) to change pattern.
- Rate the step. Press OK (Enter), choose Pass, Fail or Skip with the arrows and press OK again. The test moves to the next step. ▲ and ▼ jump between steps.
- Review the summary. Results are saved in the browser, so you can stop and continue later.
What each step checks
| Step | Look for | Usually normal | Worth returning |
|---|---|---|---|
| 1. Dead pixels | Black dots on colors, colored dots on black | None | Any bright pixel in the viewing area; clusters or lines |
| 2. Uniformity & DSE | Vertical bands, dark corners, blotches, smudges that stay put while the pattern pans | Slight darkening at the corners, faint banding at 5% on OLED | Obvious bands or a dirty patch visible in sports and pans |
| 3. Black & blooming | Light leaking from edges, halos around the white box, gray “black” | Faint edge glow on LCD; some halo on local dimming | Bright corner flashlighting at moderate brightness |
| 4. Banding | Visible steps or color bands in smooth ramps | Faint steps in the darkest part of the ramp | Strong bands in mid-tones, colored stripes in gray ramps |
| 5. Motion | Smearing, stutter, uneven speed, trails | Sample-and-hold blur; judder in the 24 fps lane | Stutter in the full-rate lane, dark trails or color fringes |
| 6. Overscan | Missing outer lines, blurry or wavy pixel pattern | — | Not a defect: fix it in settings (see below) |
Each of these has a detailed single-purpose test: dead pixels, gray uniformity and DSE, blooming, backlight bleed, color banding and ghosting.
Fix it in the TV settings first
| Problem | Setting to check |
|---|---|
| Outer lines missing in step 6 | Picture size / aspect: Just Scan (LG), Fit to Screen (Samsung), Full Pixel (Sony), “Screen Fit” or “Dot by Dot” on others |
| Halos on text or patterns | Sharpness to 0 or neutral; turn off “super resolution” and edge enhancement |
| Banding in ramps | Turn off dynamic contrast; try “smooth gradation” / noise reduction set to low; check the source sends 8-bit or higher full RGB |
| Crushed or gray blacks | Match black level / HDMI range (“Limited” vs “Full”) between the source and the TV |
| Soap opera look or stutter | Motion smoothing: TruMotion (LG), Auto Motion Plus / Picture Clarity (Samsung), Motionflow (Sony) |
| Brightness changes by itself | Energy saving, ambient light sensor, and on OLED the automatic brightness limiter |
Testing from the TV browser, a laptop or casting
- Laptop over HDMI is the most reliable: set the TV as the main or extended display at its native resolution (usually 3840 × 2160) and 100% or 200% scaling, then open the page fullscreen on it.
- TV browsers often render at 1920 × 1080 and upscale to 4K. Colors, uniformity, black level and motion are still valid, but the 1-pixel pattern in step 6 can’t map 1:1 then.
- Casting a tab sends a compressed video stream. It is fine for dead pixels, uniformity and black level, but it adds its own banding, blur and stutter.
Test new TVs as soon as they arrive. Store return windows are usually much easier to use than a manufacturer’s warranty, which may not cover uniformity, DSE or a few dead pixels at all.
OLED vs LCD: what to expect
On OLED TVs, black is truly black and there is no blooming or bleed, but near-black (step 2’s 5% field) often shows faint vertical bands or a slight tint, and very dark gradients can show steps. On LCD TVs, black is a dark gray with some edge glow, local dimming adds halos around bright objects, and large panels often show some dirty screen effect. Judge against reviews of the same model rather than against perfection; the OLED test covers OLED-specific checks in more detail.
Frequently asked questions
How do I test a new TV for defects?
Let it warm up for 20–30 minutes, switch to the Movie or Filmmaker picture mode, and turn off energy saving. Then open this page in the TV’s browser — or on a laptop connected by HDMI — go fullscreen and work through the six steps with the remote: dead pixels, uniformity and dirty screen effect, black level and blooming, banding, motion, and overscan. Mark each one Pass or Fail with OK.
Can I use this test from my TV’s built-in browser?
Yes. It works in the browsers on LG webOS, Samsung Tizen, Android/Google TV and Fire TV, and needs only the arrow keys and OK. Some TV browsers don’t support true fullscreen, in which case the test fills the browser window; hide the browser’s address bar if it has an option. For the most reliable results, connect a laptop with HDMI and use this page fullscreen at the TV’s native resolution.
Can I cast this test to my TV?
You can, and it is fine for dead pixels, uniformity and black level. Don’t use casting to judge banding, fine detail or motion: tab casting compresses the image as video and can run at a lower frame rate, which adds its own banding, blur and stutter. Use the TV’s browser or an HDMI cable for those steps.
What is the dirty screen effect?
Dirty screen effect (DSE) is uneven brightness that looks like smudges, vertical bands or a darker center on a uniform image. It is most noticeable when the camera pans across a uniform area, such as a football field or ice rink. Some DSE is common on large LCD and OLED TVs; check it on the 5–20% gray fields and the panning pattern, and compare with reviews of the same model.
What is overscan and how do I turn it off?
Overscan crops the edges of the picture and enlarges the rest, which hides the outer lines in our last step and blurs fine detail. Turn it off in the picture size settings: Just Scan or “Original” on LG, Fit to Screen on Samsung, Full Pixel on Sony, and Screen Fit or “Dot by Dot” on many others.
Why does motion look blurry or stutter on my TV?
Sample-and-hold blur is normal on every LCD and OLED, and 24 fps film judders on any display — the 24 fps lane in the motion step shows how much. TVs offer motion smoothing (TruMotion, Auto Motion Plus, Motionflow) to reduce both; it can create the “soap opera effect”. Game mode turns most processing off for lower input lag.
How much backlight bleed or blooming is normal on a TV?
Some is normal on any LCD TV: a little edge glow on a black screen in a dark room, and a soft halo around bright objects on local-dimming (FALD or mini-LED) sets. Bright patches visible in normal viewing, or flashlighting in the corners during dark movie scenes at moderate brightness, are worth returning within the store’s return window.
Last updated . Runs entirely in your browser — nothing is uploaded.