How to run the phone screen test
- Prepare the phone. Clean the screen, take off the case, and turn brightness up to maximum. Turn off dark mode extensions, Night Shift / Night Light / Eye Comfort, and battery saver if they tint or dim the screen.
- Tap the test. It fills the screen (on iPhone, it fills the browser window — see the FAQ for a true edge-to-edge view). Turn the phone so the screen faces you squarely.
- Work through each step. Tap the screen to change the pattern within a step. When you are done looking, tap Pass or Fail; the test moves on automatically.
- Touch steps: slide a finger over every cell of the grid until it is all blue, then put down as many fingers as you can for the multi-touch count.
- Read the summary. Results are stored on the phone, so you can leave and come back. Copy report gives you a text summary for a seller, buyer or repair shop.
What each step checks
| Step | Look for | Normal |
|---|---|---|
| Dead pixels | Black dots on white and colors; colored or white dots on black | No dots at all — phones rarely ship with any |
| Tint & uniformity | Yellow, pink or green patches; a tinted corner or edge; clouding | Even white; slight warmth from True Tone or adaptive color |
| Burn-in | Ghost outlines of the status bar, nav bar, keyboard or app icons | Nothing visible at any color |
| Black & near-black | Glowing black (OLED models), grainy or blotchy dark gray, color cast | Black is fully off on OLED; slight grain at 2% gray is common |
| Touch grid | Cells that won’t light up (dead zones), especially at edges | 100% coverage |
| Multi-touch | Fingers that don’t register or merge | 5 or more simultaneous touches |
For a closer look at any one problem, the single-purpose tests go deeper: dead pixel test, burn-in test, OLED test and the full touch screen test with ghost-touch detection.
Buying a used phone: screen checklist
Run this whole test in person before you pay, with the seller’s case and screen protector removed. Then go through the list below — most of it takes a minute.
Every phone
- Burn-in at full brightness. Pay attention to the keyboard area, the navigation bar or gesture pill and the status bar. Phones used as GPS units or for one app all day often have burned-in toolbars.
- Touch across the whole screen. The grid should reach 100%, including the corners. Dead strips usually mean a damaged or poorly fitted replacement digitizer.
- Ghost touches while charging. Plug in the charger and leave the phone on the touch test’s ghost watch for 30 seconds.
- Screen edges and frame. Look along the edge from a low angle. A screen that lifts, bulges or has a gap at one side can mean a swelling battery — walk away.
- Pressure marks and bright spots on white (LCD models), which come from drops or pressure in a pocket.
- Scratches on a white screen and with the screen off, under a light source at an angle.
- Proximity sensor: during a call, the screen should turn off when you hold the phone to your ear.
- Auto-brightness: with it turned on, covering the top of the phone with your hand should dim the screen after a moment.
iPhone
- Parts and Service History (Settings → General → About, on iPhone XR/XS and later with a recent iOS): a non-genuine display is shown as “Unknown Part”.
- True Tone (iPhone 8 and later): long-press the brightness slider in Control Center — the True Tone button should be there.
- OLED or LCD? iPhone X and later are OLED, except the XR, 11 and SE models. On an OLED model, the Black pattern in a dark room should be indistinguishable from the phone being off. A gray glow means a cheaper LCD replacement screen.
- Face ID: set up a new face in Settings → Face ID & Passcode. A failed screen repair can damage the sensors around the notch or Dynamic Island.
Android
- Samsung Galaxy: many models open a hardware test menu when you dial
*#0*#in the Phone app, with color fields and a touch test. It can be disabled on carrier models. - Green or pink tint at low brightness on dark gray — compare against a phone of the same model if you can.
- In-display fingerprint reader: enroll a finger and test it a few times. Aftermarket screens often break or weaken it.
- Refresh rate: if the phone has a 90 or 120 Hz screen, check it in our refresh rate test — some replacement screens only run at 60 Hz.
A replaced screen isn’t automatically bad, but it should be reflected in the price and disclosed by the seller. Original OLED screens are expensive to replace, so low-cost repairs often use LCD or lower-grade OLED panels with worse brightness, color and battery life.
Normal or a defect?
- Normal: slight warm or cool shifts when tilting an OLED phone, faint grain on near-black at the lowest brightness, slightly different white between two units of the same model, and the screen warming up in color with True Tone or adaptive color on.
- Defects: any dead or stuck pixel, visible burn-in, touch dead zones, ghost touches, a screen that flickers or shows lines, a clearly uneven tint across the screen at normal brightness, and lifting at the edges.
For a new phone, raise any defect within the store’s return window — it is almost always easier than a warranty claim.
Frequently asked questions
How do I test my phone screen?
Open this page on the phone, tap the test to make it fill the screen, and follow the six steps: dead pixels, color tint, burn-in, black level, a touch grid and multi-touch. Mark each step Pass or Fail; your results are saved on the phone and summarized at the end.
How do I check a used phone for burn-in?
Set brightness to maximum, open the Burn-in step and look at where the status bar, the navigation bar or gesture pill, and the keyboard normally sit. A faint outline of icons, keys or a bar that stays in the same place on every color is burn-in. Gray and red usually show it best.
How can I tell if an iPhone screen has been replaced?
On iPhone XR, XS and later with a recent iOS version, go to Settings → General → About and look for Parts and Service History; a non-genuine display shows as “Unknown Part”. Other signs: True Tone missing from Control Center’s brightness controls, a gray glow on a black screen in a dark room on a model that should have OLED, slightly thicker black borders, and touch that feels less precise.
Is a green or pink tint on my phone screen normal?
A slight tint at very low brightness, especially on dark gray, is common on OLED phones and varies from unit to unit. A tint that is obvious at normal brightness, or that differs between the top and bottom of the screen, is worth raising while you are in the return window.
Why does the test not fill my whole iPhone screen?
iPhone Safari doesn’t allow web pages to go truly fullscreen, so the test fills the browser window. Scroll down slightly or rotate to landscape and back to shrink the address bar, or add the page to your home screen (Share → Add to Home Screen) and open it from there for an edge-to-edge view.
Can this test check the screen’s brightness or color accuracy?
No — a web page can’t measure light. It shows patterns that make defects visible to your eye. Peak brightness and color accuracy need a meter. What you can check by eye: auto-brightness reacting when you cover the top of the phone, and True Tone or adaptive color shifting the white point under warm light.
Last updated . Runs entirely in your browser — nothing is uploaded.